Price: $18.99 - $15.99
(as of Jun 05,2023 02:26:12 UTC – Details)
Product Description
Power Supply Tester – Aluminum Alloy Enclosure
[8-in-1 ATX Power Supply Tester] — Support test 20-pin IDE / 24-pin IDE / HDD / Floppy 4-pin / PCI-e 6-pin / 4-pin / 8-pin / SATA connectors [Aluminum Alloy Enclosure] — Light and Easy to Carry, High Strength, Nice Thermal Conductivity & Corrosion Resistance [1.8” LCD Screen] — Outputted Voltages shows on the 1.8” LCD Screen, Easy to Read (The 1.8” LCD Screen was Powered by 20-pin / 24-pin Connector)[Beep Alarm] — When your power supply test value is beyond normal range, the Power Supply Tester would issue a buzzer alarm, Easy to Know
Operation method:
Insert the power 20-pin or 24-pin and P4, P6 or P8 plug into the corresponding position of the power tester. (if Insert the 20pin or 24pin connector, tester alarms and displays “LL”, it needs to plug in 4P connector! Please make sure 4P connector is inserted in 4P position! )Turn on the power supply, at the same time, “didi” sounds twice. If the values of each group do not flash, it indicates that the power input of this power supply is normal.The voltage of IDE / SATA / P6 / P8 interface is displayed by the three lights on the left of the power tester. If their voltage is normal, the three groups of lights (+ 12V, + 3.3, + 5V) will be on. If the light is not on, it indicates that the interface line group is faulty.If the voltage signal of a circuit is not detected (such as 20-pin or 24-pin connector) or the detected voltage exceeds the normal range, the buzzer will send out a warning sound of “di di” for a long time, and the corresponding voltage or PG value display status is flashing state, it means that the power supply is a fault source!Special reminder: The power supply tester is not supported Hot Plug
How to judge test results？
The voltage of 20-pin / 24-pin / P4 interface is displayed by the 1.8” LCD Screen. If their test voltage is exceeds the normal range, the buzzer will send out a warning sound of “di di” for a long time, and the corresponding voltage or PG value display status is flashing state, it means that the power supply is a fault source.The voltage of IDE / SATA / P6 / P8 interface is displayed by the three lights on the left of the power tester. If their voltage is normal, the three groups of lights (+ 12V, + 3.3, + 5V) will be on. If the light is not on, it indicates that the interface line group is faulty.
NOTE:
The power tester has no battery and is completely powered by 20-pin or 24-pin interface, if there is no 20-pin or 24-pin interface powered, tester screen will not light up and the value cannot be read. The Product Screen Has Scratches？Because the LCD screen is easy to scratch, we put aprotective film on It, if you think It’s not beautiful and useless, you can tear it off by yourself. The protective film of the screen fits very well and is not easy to tear off. Please operate carefully to avoid scratching the LCD screen. Please do not plug the interface in the wrong position or reverse, which may cause the power tester to smoke or damage your power supply. Special reminder: not supported Hot Plug, Hot Plug behavior can cause short circuits or other problems
Condition: 100% NewColor: BlackMaterial: Aluminum AlloyScreen: 1.8” LCD ScreenCharacteristics: Beep Alarm when power supply was problemItem Dimensions: 4.9” x 2.6”x 0.63”Item Weight: 3.1 ounces
Package Includes:1x Power Supply Tester – Aluminum Alloy Enclosure
[8-in-1 ATX Power Supply Tester] — Support test 20-pin IDE / 24-pin IDE / HDD / Floppy 4-pin / PCI-e 6-pin / 4-pin / 8-pin / SATA connectors
[Aluminum Alloy Enclosure] — Light and Easy to Carry, High Strength, Nice Thermal Conductivity & Corrosion Resistance
[1.8” LCD Screen] — Outputted Voltages shows on the 1.8” LCD Screen, Easy to Read ( The 1.8” LCD Screen was Powered by 20-pin / 24-pin Connector ), Note: The Product Screen Has a Load of Scratches All Over It？Because The Screen is Easy to Scratch, We Put a Protective Film on It, If You Think It’s Not Beautiful, You Can Tear It Off by Yourself
[Beep Alarm] — When your power supply test value is beyond normal range, the Power Supply Tester would issue a buzzer alarm, Easy to Know
NOTE: The voltage of IDE / SATA / P6 / P8 interface is displayed by the three lights on the left of the power tester. If their voltage is normal, the three groups of lights (+ 12V, + 3.3, + 5V) will be on. If the light is not on, it indicates that the interface line group is faulty
){kind=link}